How to Receive SMS Messages Using a Computer / PC?

In general, there are three ways to receive SMS messages using your computer / PC:

1. Connect a mobile phone or GSM/GPRS modem to a computer / PC. Then use the computer / PC and AT commands to get the received SMS messages from the mobile phone or GSM/GPRS modem.


2. Get access to the SMS center (SMSC) or SMS gateway of a wireless carrier. Any SMS messages received will be forwarded to your computer / PC using a protocol / interface supported by the SMSC or SMS gateway.


3. Get access to the SMS gateway of an SMS service provider. Any SMS messages received will be forwarded to your computer / PC using a protocol / interface supported by the SMS gatewaay

Using a Computer to Receive SMS Messages through a Mobile Phone or GSM/GPRS Modem

Receiving SMS messages through a mobile phone or GSM/GPRS modem has a major advantage over the other two ways -- wireless carriers usually do not charge any fees for receiving incoming SMS messages with their SIM cards. The disadvantage of receiving SMS messages this way is that a mobile phone or GSM/GPRS modem cannot handle a large amount of SMS traffic. One way to overcome this is to load balance the SMS traffic with a pool of mobile phones or GSM/GPRS modems. Each mobile phone or GSM/GPRS modem will have its own SIM card and mobile phone number.

In terms of programming, sending and receiving SMS messages through a mobile phone or GSM/GPRS modem are similar. What you need to do is to send instructions (in the form of AT commands) to the mobile phone or GSM/GPRS modem.

The following table lists the AT commands that are related to the receiving and reading of SMS messages:

AT command	Meaning
+CNMI	New message indications
+CMGL	List messages
+CMGR	Read messages
+CNMA	New message acknowledgement

Below shows a simple example that demonstrates how to use AT commands and the HyperTerminal program of Microsoft Windows to read SMS text messages received by a GSM / GPRS modem or mobile phone. The lines in bold type are the command lines that should be entered in HyperTerminal. The other lines are responses returned from the GSM / GPRS modem or mobile phone.

AT
OK
AT+CMGF=1
OK
AT+CMGL="ALL"
+CMGL: 1,"REC READ","+85291234567",,"06/11/11,00:30:29+32"
Hello, welcome to our SMS tutorial.
+CMGL: 2,"REC READ","+85291234567",,"06/11/11,00:32:20+32"
A simple demo of SMS text messaging.

OK

Here is a description of what is done in the above example:

• Line 1: "AT" is sent to the GSM / GPRS modem to test the connection. The GSM / GPRS modem sends back the result code "OK" (line 2), which means the connection between the HyperTerminal program and the GSM / GPRS modem works fine.


• Line 3: The AT command +CMGF is used to instruct the GSM / GPRS modem to operate in SMS text mode. The result code "OK" is returned (line 4), which indicates the command line "AT+CMGF=1" has been executed successfully. If the result code "ERROR" is returned, it is likely that the GSM / GPRS modem does not support the SMS text mode. To confirm, type "AT+CMGF=?" in the HyperTerminal program. If the response is "+CMGF: (0,1)" (0=PDU mode and 1=text mode), then SMS text mode is supported. If the response is "+CMGF: (0)", then SMS text mode is not supported.


• Line 5-9: The AT command +CMGL is used to list all SMS text messages in the message storage of the GSM / GPRS modem. There are two SMS text messages in the message storage: "Hello, welcome to our SMS tutorial." and "A simple demo of SMS text messaging.". "+85291234567" is the sender mobile phone number. "06/11/11,00:30:29+32" and "06/11/11,00:32:20+32" tell us when the SMS text messages were received by the SMSC. "+32" is the time zone. Note that the unit is a quarter of an hour. So, +32 means GMT+8 hours, since 32 quarters of an hour = 8 hours. "REC READ" indicates both of the SMS text messages have been read before.


• Line 11: The result code "OK" indicates the execution of the AT command +CMGL is successful.

To enable an application to receive SMS messages, you have to write the source code for connecting to and sending AT commands to the mobile phone or GSM/GPRS modem, just like what a terminal program (such as HyperTerminal of Microsoft Windows) does. You can write the source code in C, C++, Java, Visual Basic, Delphi or other programming languages you like.

However, like what we have discussed in the earlier section "The 1st Way: Sending SMS Messages from a Computer Using a Mobile Phone or GSM/GPRS Modem", usually a better solution is to use a high-level SMS messaging API (Application programming interface) / SDK (Software development kit) / library instead of writing your own code for interacting with the mobile phone or GSM/GPRS modem via AT commands. The API / SDK / library encapsulates the low-level details. So, an SMS application developer does not need to know AT commands and the composition of SMS messages in the bit-level. Some SMS messaging APIs / SDKs / libraries support SMSC protocols in addition to AT commands. To move from a wireless-modem-based SMS solution to a SMSC-based SMS solution, usually you just need to modify a configuration file / property file or make a few changes to your SMS messaging application's source code. The links to some open source and free SMS messaging libraries can be found in the article "Free Libraries/Tools for Sending/Receiving SMS with a Computer".

Another high-level solution is to place an SMS gateway between the SMS messaging application and the mobile phone or GSM/GPRS modem. The SMS messaging application can then use simple protocols such as HTTP / HTTPS for receiving SMS messages. If an SMSC protocol (e.g. SMPP, CIMD, etc) is used for communicating with the SMS gateway instead of HTTP / HTTPS, an SMS messaging API / SDK / library can be very helpful to you since it encapsulates the SMSC protocol's details.

// //

// //